화학공학소재연구정보센터
홈 로그인 로그아웃 연락처 사이트맵
Polymer(Korea), Vol.36, No.5, 606-611, September, 2012
Export Citation
전기방사법으로 제조한 PEI/PVdF 블렌드 웹의 물리적 특성에 대한 후처리 영향
Effect of Post-Process on Physical Properties of Electrospun PEI/PVdF Blend Nonwoven Web
석훈1, 2, 박철민2, 김동영1, 조성무1, †
  • 1한국과학기술연구원 다원물질융합연구소 물질구조제어연구단
  • 2연세대학교 신소재공학과
Hoon Seok1, 2, Cheolmin Park2, Dong Young Kim1, and Seong Mu Jo1, †
  • 1Center for Materials Architecturing, Institute of Multi-disciplinary Convergence of Matters, Korea Institute of Science and Technology, Seoul 136-791, Korea
  • 2Department of Material Science and Engineering, Yonsei University, Seoul 120-749, Korea
E-mail:
초록
Polyetherimide(PEI)와 poly(vinylidene flouride)(PVdF) 폴리머들을 블렌딩하여 전기방사를 통해 웹을 제조하였다. 낮은 기계적 물성을 증대시키기 위해서 압착과 연신이라는 후처리 공정을 이용하였으며 후처리 공정이 기계적 물성에 미치는 영향을 조사하였다. 물리적 특성을 확인하기 위해 SEM, 인장 시험 측정기를 이용하여 측정하였다. 180 ℃의 압착 온도에서 1/2, 1/3, 1/4, 1/5의 비율로 압착된 웹들은 초기 상태에 비해 대략 4~5배 가량 인장 강도가 증가하였으며, 이들을 220 ℃의 온도에서 30~40% 연신함으로써 2~8MPa의 추가적인 인장 강도 증대를 보였다.
Polyetherimide (PEI) and poly(vinylidene fluoride) (PVdF) blend web was prepared by electrospinning technique. In order to improve low mechanical properties, post processes like hot-pressing and heat-stretching were employed, and a study on the effects of post processes on their mechanical properties was performed. To confirm the physical properties of the web, scanning electron microscopy and tensile measuring instrument were used. The mechanical strength of webs pressed in the ratios of 1/2, 1/3, 1/4 and 1/5 at 180 ℃ were improved four-to-five times compared to pristine webs. Also they showed an additional increase by 2~8MPa, by heat-stretching 30 to 40% at 220 ℃.
Keywords:PEI/PVdF blend web;mechanical strength;hot-pressing;heat-stretching;physical properties.
  1. Megelski S, Stephens JS, Chase DB, Rabolt JF, Macromolecules, 35(22), 8456 (2002)
  2. Huang ZM, Zhang YZ, Kotaki M, Ramakrishna S, Compos. Sci. Technol., 63, 2223 (2003)
  3. Sun ZC, Zussman E, Yarin AL, Wendorff JH, Greiner A, Adv. Mater., 15(22), 1929 (2003)
  4. Fang Y, Chen HZ, Yang HY, Li HY, Mang W, Mater. Chem. Phys., 89(2-3), 390 (2005)
  5. Faridi-Majidi R, Sharifi-Sanjani N, J. Appl. Polym. Sci., 105(3), 1351 (2007)
  6. Choi SW, Kim JR, Jo SM, Lee WS, Kim YR, J. Electrochem. Soc., 152(5), A989 (2005)
  7. Jo SM, Jang SY, Polymer Science and Technology., 19, 1 (2008)
  8. Kim JR, Choi SW, Jo SM, Lee WS, Kim BC, Electrochim. Acta, 50(1), 69 (2004)
  9. Choi SW, Jo SM, Lee WS, Kim YR, Adv. Mater., 15(23), 2027 (2003)
  10. Kim JR, Choi SW, Jo SM, Lee WS, Kim BC, J. Electrochem. Soc., 152(2), A295 (2005)
  11. Lee SW, Choi SW, Jo SM, Chin BD, Kim DY, Lee KY, J. Power Sources, 163(1), 41 (2006)
  12. Choi SW, Kim JR, Ahn YR, Jo SM, Cairns EJ, Chem. Mater., 19, 104 (2007)
  13. Rosario RES, Donald GB, Polymer., 33, 5233 (1992)
  14. Koombhongse S, Liu WX, Reneker DH, J. Polym. Sci. B: Polym. Phys., 39(21), 2598 (2001)
  15. Casper CL, Stephens JS, Tassi NG, Chase DB, Rabolt JF, Macromolecules, 37(2), 573 (2004)
  16. Mit-uppatham C, Nithitanakul M, Supaphol P, Macromol.Chem. Phys., 205, 2327 (2004)
  17. Theron SA, Zussman E, Yarin AL, Polymer, 45(6), 2017 (2004)
  18. Lee GH, Jung IT, Shim SH, Yoon KB, Polymer Science and Technology., 19, 1 (2008)
  19. Kim HS, Lee DY, Park YJ, Kim JH, Appl. Chem., 1(2), 349 (1997)
  20. Repka MA, McGinity JW, Biomaterials., 21, 1509 (2000)
  21. Jeong BY, Cheon JM, Yoo CS, Chun JW, J. Adhesion Interface., 9, 12 (2008)
  22. Hwang TS, Lee SG, Cha KS, Polym.(Korea), 25(6), 774 (2001)
  23. Park JH, Sung YT, Kim WN, Hong JH, Hong BK, Yoo TW, Yoon HG, Polym.(Korea), 29(1), 19 (2005)