Energy Conversion and Management

Energy Conversion and Management, Vol.75 Entire volume, number list

ISSN: 0196-8904 (Print)

In this Issue (85 articles)

1 - 10	Study on soot formation characteristics in the diesel combustion process based on an improved detailed soot model Cheng XB, Chen L, Yan FQ, Dong SJ
11 - 20	Comparative analysis of dynamic line rating models and feasibility to minimise energy losses in wind rich power networks Simms M, Meegahapola L
21 - 24	Biogas performance from co-digestion of Taihu algae and kitchen wastes Zhao MX, Ruan WQ
25 - 35	Numerical investigation on effect of riser diameter and inclination on system parameters in a two-phase closed loop thermosyphon solar water heater Aung NZ, Li SJ
36 - 43	Effect of flow rate, flow direction, and silica addition on the performance of membrane and the corrosion behavior of Pt-Ru/C catalyst in PEMFC Saeed F, Saidan M, Said A, Mustafa M, Abdelhadi A, Al-Weissi S
44 - 50	Hydrodynamics performance of hydrofoil-slat arrangements in 3D analysis Yavuz T, Koc E, Kaynak B
51 - 60	Performance comparison of liquid desiccant air handling processes from the perspective of match properties Zhang T, Liu XH, Jiang Y
61 - 73	Optimisation-oriented modelling of the NOx emissions of a Diesel engine Asprion J, Chinellato O, Guzzella L
74 - 85	Development, validation and application of a fixed district heating model structure that requires small amounts of input data Aberg M, Widen J
86 - 97	Modeling and optimization of hybrid wind-solar-powered reverse osmosis water desalination system in Saudi Arabia Mokheimer EMA, Sahin AZ, Al-Sharafi A, Ali AI
98 - 104	Exergy analyses in cement production applying waste fuel and mineralizer Reno MLG, Torres FM, da Silva RJ, Santos JJCS, Melo MDNM
105 - 117	Numerical simulation of a cooling tower coupled with heat pump system associated with single house using TRNSYS Chargui R, Sammouda H, Farhat A
118 - 129	Low and medium temperature solar thermal collector based in innovative materials and improved heat exchange performance Fernandez A, Dieste JA
130 - 140	Application of computational intelligence techniques for load shedding in power systems: A review Laghari JA, Mokhlis H, Bakar AHA, Mohamad H
141 - 151	Waste heat recovery from the exhaust of a diesel generator using Rankine Cycle Hossain SN, Bari S
152 - 161	Modeling and simulation to determine the potential energy savings by implementing cold thermal energy storage system in office buildings Rismanchi B, Saidur R, Masjuki HH, Mahlia TMI
162 - 174	Electrochemical-thermal analysis of 18650 Lithium Iron Phosphate cell Saw LH, Ye YH, Tay AAO
175 - 183	Parametric study of a single cycle two-stage structured packing counter flow air dehumidifier using two feeding desiccant solution lines Bassuoni MM
184 - 190	Numerical analysis on the effect of swirl ratios on swirl chamber combustion system of DI diesel engines Wei SL, Wang FH, Leng XY, Liu X, Ji KP
191 - 201	Estimation of the temperature, heat gain and heat loss by solar parabolic trough collector under Algerian climate using different thermal oils Ouagued M, Khellaf A, Loukarfi L
202 - 213	Thermo-economic assessment of externally fired micro-gas turbine fired by natural gas and biomass: Applications in Italy Pantaleo AM, Camporeale SM, Shah N
214 - 223	Impact of the use of a hybrid turbine inlet air cooling system in arid climates Al-Ansary HA, Orfi JA, Ali ME
224 - 233	Performance and emission characteristics of biogas used in diesel engine operation Makareviciene V, Sendzikiene E, Pukalskas S, Rimkus A, Vegneris R
234 - 240	Energy analysis and improvement potential of finned double-pass solar collector Fudholi A, Sopian K, Othman MY, Ruslan MH, Bakhtyar B
241 - 248	Integration of thermal insulation coating and moving-air-cavity in a cool roof system for attic temperature reduction Yew MC, Sulong NHR, Chong WT, Poh SC, Ang BC, Tan KH
249 - 255	Assessment of energy generation potentials of MSW in Delhi under different technological options Chakraborty M, Sharma C, Pandey J, Gupta PK
256 - 262	Assessment of bioelectricity production in microbial fuel cells through series and parallel connections Jafary T, Rahimnejad M, Ghoreyshi AA, Najafpour G, Hghparast F, Daud WRW
263 - 270	Thermal and kinetic behaviors of biomass and plastic wastes in co-pyrolysis Cepeliogullar O, Putun AE
271 - 281	Design of an optimized photovoltaic and microturbine hybrid power system for a remote small community: Case study of Palestine Ismail MS, Moghavvemi M, Mahlia TMI
282 - 291	Designing a solar powered Stirling heat engine based on multiple criteria: Maximized thermal efficiency and power Ahmadi MH, Sayyaadi H, Dehghani S, Hosseinzade H
292 - 301	First in situ operation performance test of ground source heat pump in Tunisia Naili N, Attar I, Hazami M, Farhat A
302 - 310	Two-stage continuous process of methyl ester from high free fatty acid mixed crude palm oil using static mixer coupled with high-intensity of ultrasound Somnuk K, Smithmaitrie P, Prateepchaikul G
311 - 318	Assessing the potential of support vector machine for estimating daily solar radiation using sunshine duration Chen JL, Li GS, Wu SJ
319 - 324	Thermodynamic analysis of a beta-type Stirling engine with rhombic drive mechanism Aksoy F, Cinar C
325 - 335	Investigating the thermodynamics and economics of operating the thermal power plant under uncertain conditions Al-Mutairi EM, Odejobi OJ
336 - 347	Heat flux and acoustic power in a convection-driven T-shaped thermoacoustic system Li SH, Zhao D
348 - 365	Sizing a solar dish Stirling micro-CHP system for residential application in diverse climatic conditions based on 3E analysis Moghadam RS, Sayyaadi H, Hosseinzade H
366 - 373	Optical, geometric and thermal study for solar parabolic concentrator efficiency improvement under Tunisia environment: A case study Skouri S, Ben Salah M, Bouadila S, Balghouthi M, Ben Nasrallah S
374 - 388	Sustainable urban rail systems: Strategies and technologies for optimal management of regenerative braking energy Gonzalez-Gil A, Palacin R, Batty P
389 - 397	Analysis of a Spanish energy scenario with Generation IV nuclear reactors Ochoa R, Jimenez G, Perez-Martin S
398 - 401	New insights for renewable energy hybrid photovoltaic/wind installations in Tunisia through a mathematical model Colantoni A, Allegrini E, Boubaker K, Longo L, Di Giacinto S, Biondi P
402 - 406	An assessment of the potential contribution from waste-to-energy facilities to electricity demand in Saudi Arabia Ouda OKM, Cekirge HM, Raza SAR
407 - 417	A novel application of reactive absorption to break the CO2-ethane azeotrope with low energy requirement Tavan Y, Hosseini SH
418 - 424	Calculating electrical and thermal characteristics of multiple PV array configurations installed in the tropics Ya'acob ME, Hizam H, Htay MT, Radzi MAM, Khatib T, Bakri A M
425 - 430	Thermogravimetric study of biomass, sewage sludge and coal combustion Magdziarz A, Wilk M
431 - 437	Roles of inherent mineral matters for lignite water slurry electrolysis in H2SO4 system Gong XZ, Wang MY, Wang Z, Guo ZC
438 - 445	Multi-objective thermodynamic-based optimization of output power of Solar Dish-Stirling engine by implementing an evolutionary algorithm Ahmadi MH, Mohammadi AH, Dehghani S, Barranco-Jimenez MA
446 - 452	Energy optimisation and layout of a membrane-free OSEC system for the hypochlorite self-production in Developing Countries Dell'Era A, Zuccari F, Santiangeli A, Fiori C, Micangeli A, Orecchini F
453 - 465	Simulation of cogeneration within the concept of smart energy networks Chai DS, Wen JZ, Nathwani J
466 - 473	Analysis of the heat transfer mechanisms during energy storage in a Phase Change Material filled vertical finned cylindrical unit for free cooling application Solomon GR, Velraj R
474 - 481	Influence of oily wastes on the pyrolysis of scrap tire Siva M, Onenc S, Ucar S, Yanik J
482 - 487	Aqueous preparation of polyethylene glycol/sulfonated graphene phase change composite with enhanced thermal performance Li HR, Jiang M, Li Q, Li DN, Chen ZY, Hu WP, Huang J, Xu XZ, Dong LJ, Xie HA, Xiong CX
488 - 497	Energy and exergy assessments of a perlite expansion furnace in a plaster plant Gurturk M, Oztop HF, Hepbasli A
498 - 508	Tractor's engine performance and emission characteristics in the process of ploughing Janulevicius A, Juostas A, Pupinis G
509 - 516	Comparative evaluation of a natural gas expansion plant integrated with an IC engine and an organic Rankine cycle Kostowski WJ, Uson S
517 - 522	Wind power variations under humid and arid meteorological conditions Sen Z
523 - 531	Study of knock in a high compression ratio SI methanol engine using LES with detailed chemical kinetics Zhen XD, Wang Y, Zhu YS
532 - 541	A study on heat transfer enhancement using flow channel inserts for thermoelectric power generation Lesage FJ, Sempels EV, Lalande-Bertrand N
542 - 551	Development and optimization of a PV/diesel hybrid supply system for remote controlled commercial large scale FM transmitters Moghavvemi M, Ismail MS, Murali B, Yang SS, Attaran A, Moghavvemi S
552 - 560	Development of a new concept solar-biomass cogeneration system Angrisani G, Bizon K, Chirone R, Continillo G, Fusco G, Lombardi S, Marra FS, Miccio F, Roselli C, Sasso M, Solimene R, Tariello F, Urciuolo M
561 - 569	Forecasting hourly global solar radiation using hybrid k-means and nonlinear autoregressive neural network models Benmouiza K, Cheknane A
570 - 580	Investigation and analysis on the energy consumption of starred hotel buildings in Hainan Province, the tropical region of China Lu SL, Wei SS, Zhang K, Kong XF, Wu W
581 - 592	A novel engine cooling system with two circuits operating at different temperatures Cipollone R, Di Battista D, Gualtieri A
593 - 602	Contribution to the study of the wind and solar radiation over Guadeloupe Bertin A, Frangi JP
603 - 608	Thermochemical characterization of banana leaves as a potential energy source Fernandes ERK, Marangoni C, Souza O, Sellin N
609 - 616	Experimental study on the heat recovery characteristics of a new-type flat micro-heat pipe array heat exchanger using nanofluid Zhang J, Diao YH, Zhao YH, Tang X, Yu WJ, Wang S
617 - 628	Simulation of energy saving potential of a centralized HVAC system in an academic building using adaptive cooling technique Bhaskoro PT, Gilani SIU, Aris MS
629 - 634	Performance testing of a Fresnel/Stirling micro solar energy conversion system Aksoy F, Karabulut H
635 - 642	Optimal design of a solar driven heat engine based on thermal and thermo-economic criteria Ahmadi MH, Dehghani S, Mohammadi AH, Feidt M, Barranco-Jimenez MA
643 - 650	Multi-agent modeling for the simulation of a simple smart microgrid Kremers E, Gonzalez de Durana J, Barambones O
651 - 657	Assessing the PV business opportunities in Greece Patlitzianas KD, Skylogiannis GK, Papastefanakis D
658 - 663	Influence of economical variables on a supercritical biodiesel production process Marchetti JM
664 - 672	Estimating the energy independence of a municipal wastewater treatment plant incorporating green energy resources Chae KJ, Kang J
673 - 684	Influence of individual heat pumps on wind power integration - Energy system investments and operation Hedegaard K, Munster M
685 - 700	Thermodynamic performance analysis of a vapor compression-absorption cascaded refrigeration system Jain V, Kachhwaha SS, Sachdeva G
701 - 709	Impact of onsite solar generation on system load demand forecast Kaur A, Pedro HTC, Coimbra CFM
710 - 717	Techno-economic analysis of biodiesel production from Jatropha curcas via a supercritical methanol process Yusuf NNAN, Kamarudin SK
718 - 726	Performance of direct methanol fuel cell with a palladium-silica nanofibre/Nafion composite membrane Thiam HS, Daud WRW, Kamarudin SK, Mohamad AB, Kadhum AAH, Loh KS, Majlan EH
727 - 733	Enhanced corrosion resistance and fuel cell performance of Al1050 bipolar plate coated with TiN/Ti double layer Lee EK, Kim JK, Kim TJ, Song H, Kim JH, Park SA, Jeong TG, Yun SW, Lee J, Goo J, Kim JH, Park BG, Chun HH, Song PK, Kang CG, Kim YT
734 - 740	Assessment of the achieved savings from induction motors energy efficiency labeling in Brazil Bortoni EC, Nogueira LAH, Cardoso RB, Haddad J, Souza EP, Dias MVX, Yamachita RA
741 - 747	The influence of propylene glycol ethers on base diesel properties and emissions from a diesel engine Gomez-Cuenca F, Gomez-Marin M, Folgueras-Diaz MB
748 - 760	Enhanced heat transfer with corrugated flow channel in anode side of direct methanol fuel cells Heidary H, Abbassi A, Kermani MJ
761 - 772	PV power system using hybrid converter for LED indictor applications Tseng SY, Wang HY, Chen CC
773 - 779	Experimental investigation of kapok (Ceiba pentandra) oil biodiesel as an alternate fuel for diesel engine Vedharaj S, Vallinayagam R, Yang WM, Chou SK, Chua KJE, Lee PS
780 - 795	A unified approach for designing a photovoltaic solar system for the underground water pumping well-34 at Disi aquifer Ebaid MSY, Qandil H, Hammad M