Development of a New Uniaxial Compression Test Method for paper Materials using Aluminum Honeycomb as a Lateral Supporter

Gi Jeung Um; Yong Kye Lee; Hyoung Jin Kim

Journal of Industrial and Engineering Chemistry, Vol.12, No.1, 86-90, January, 2006

Gi Jeung Um^†, Yong Kye Lee¹, and Hyoung Jin Kim²

Chang-Gang Paper Research Institute, Kangwon national University, Chuncheon, Kangwon 200-701, Korea
¹Department of Paper Science & Eng., Kangwon National University, Chuncheon, Kangwon 200-701, Korea
²Department of Forest Products, Kookmin University, Seoul 136-702, Korea

E-mail:

A novel uniaxial compression test method for paper materials using aluminum honeycomb as a lateral supporter has been successfully developed. The aluminum honeycomb was employed to prevent local buckling of the paper specimen during uniaxial compression. Overall, good agreements exist between the theoretical and experimentally measured strain values obtained using this method. The newly designed uniaxial compression test method described in this report offers several advantages for tests on flexible and thin paper specimens. It is considered that the principle of the method can be used in a uniaxial compression test for any other thin material.

Keywords:uniaxial tension test method;uniaxial compression test method;image correlation analysis;lateral supporter;buckling;constitutive model;stree-strain behavior;failure strength

[References]

Sutton MA, Chao YJ, TAPPI J., 70, 173 (1988)
Sutton MA, Chao YJ, TAPPI J., 70, 153 (1988)
Choi D, Thorpe JL, Hanna RB, Wood Sci. Technol., 25, 251 (1991)
Page DH, Seth RS, TAPPI J., 63, 99 (1980)
Seo YB, J. Pulp Pap. Sci., 25, 321 (1999)
Ramasubramanian MK, Perkins RW, J. Eng. Mater. Tech., 110, 117 (1988)
Uesaka T, in Handbook of physical and mechanical testing of paper and paperboard, Vol.1, R.E.Mark Ed., Ch.3, Marcel Dekker, Inc., New York (1983)
Nordiqvist G, Paper Timber., 32, 38 (1950)
Byrd VL, Setterholm VC, Wichman J, TAPPI J., 58, 132 (1975)
Fellers C, Svensk Papperstidn., 80, 89 (1977)
Mann RW, Baum GA, Habeger CC, TAPPI J., 63, 163 (1980)
Perkins RW, McEvoy RP, TAPPI J., 64, 99 (1981)
Gunderson DE, Appita J., 37, 137 (1983)
Setterholm VC, Gunderson DE, in Handbook of physical and mechanical testing of paper and paperboard, Vol.1, R.E.Mark Ed., Ch.4, Marcel Dekker, Inc., New York (1983)

[Referenced By]

[Related Articles]

[1] Sutton MA, Chao YJ, TAPPI J., 70, 173 (1988)

[2] Sutton MA, Chao YJ, TAPPI J., 70, 153 (1988)

[3] Choi D, Thorpe JL, Hanna RB, Wood Sci. Technol., 25, 251 (1991)

[4] Page DH, Seth RS, TAPPI J., 63, 99 (1980)

[5] Seo YB, J. Pulp Pap. Sci., 25, 321 (1999)

[6] Ramasubramanian MK, Perkins RW, J. Eng. Mater. Tech., 110, 117 (1988)

[7] Uesaka T, in Handbook of physical and mechanical testing of paper and paperboard, Vol.1, R.E.Mark Ed., Ch.3, Marcel Dekker, Inc., New York (1983)

[8] Nordiqvist G, Paper Timber., 32, 38 (1950)

[9] Byrd VL, Setterholm VC, Wichman J, TAPPI J., 58, 132 (1975)

[10] Fellers C, Svensk Papperstidn., 80, 89 (1977)

[11] Mann RW, Baum GA, Habeger CC, TAPPI J., 63, 163 (1980)

[12] Perkins RW, McEvoy RP, TAPPI J., 64, 99 (1981)

[13] Gunderson DE, Appita J., 37, 137 (1983)

[14] Setterholm VC, Gunderson DE, in Handbook of physical and mechanical testing of paper and paperboard, Vol.1, R.E.Mark Ed., Ch.4, Marcel Dekker, Inc., New York (1983)