Powder Technology

Powder Technology, Vol.273 Entire volume, number list

ISSN: 0032-5910 (Print)

In this Issue (27 articles)

1 - 7	Capillary rheology studies of INVAR 36 feedstocks for powder injection moulding Hidalgo J, Jimenez-Morales A, Barriere T, Gelin JC, Torralba JM
8 - 12	Preparation and characteristics of W-1 wt.% TiC alloy via a novel chemical method and spark plasma sintering Luo LM, Tan XY, Chen HY, Luo GN, Zhu XY, Cheng JG, Wu YC
13 - 18	Momentum transport between two granular phases of spherical particles with large size ratio: Two-fluid model versus discrete element method Jalali P, Hyppanen L
19 - 32	Performance of vertical diffusers carrying Gas-solid flow: experimental and numerical studies El-Askary WA, Ibrahim KA, El-Behery SM, Hamed MH, Al-Agha MS
33 - 39	Microwave-assisted synthesis of high purity beta-tricalcium phosphate crystalline powder from the waste of Green mussel shells (Perna canaliculus) Shavandi A, Bekhit AEDA, Ali A, Sun ZF, Ratnayake JT
40 - 46	Sintering effect on crystallite size, hydrogen bond structure and morphology of the silane-derived silicon powders Liu SS, Li H, Xiao WD
47 - 53	Characterization of nano-cemented carbides Co-doped with vanadium and chromium carbides Al-Aqeeli N
54 - 61	Wet grinding of CaCO3 with a stirred media mill: Influence of obtained particle size distributions on pressure filtration properties Kinnarinen T, Tuunila R, Huhtanen M, Hakkinen A, Kejik P, Sverak T
62 - 70	Multiple solutions of MHD boundary layer flow and heat transfer behavior of nanofluids induced by a power-law stretching/shrinking permeable sheet with viscous dissipation Dhanai R, Rana P, Kumar L
71 - 75	The use of microwave radiation for obtaining activated carbons enriched in nitrogen Kazmierczak-Razna J, Nowicki P, Pietrzak R
76 - 82	Visualization of solids phase separation in a rectangular CFB riser using a novel image calibration method Yang JS, Zhu J
83 - 90	Holdup prediction in inverse fluidization using non-Newtonian pseudoplastic liquids: Empirical correlation and ANN modeling Das B, Ganguly UP, Bar N, Das SK
91 - 101	Physicomechanical and physicochemical characterizations of biexponential compaction process of paracetamol in the presence of talcum-lubricated-MCC Panda B, Digdarsini T, Mallick S
102 - 110	A stress discontinuity approach to model the stress profile on a loaded conveyor belt Liu XW, Pang YS, Lodewijks G
111 - 117	Experimental investigation of non-stationary motion of single small spherical particles in an upward flow with different velocities Zhu C, Liu GF, Ye JX, Xu HL
118 - 124	Rheology studies of NTO-TNT based melt-cast dispersions and influence of particle-dispersant interactions Sarangapani R, Ramavat V, Reddy S, Subramanian P, Sikder AK
125 - 132	Dextran and its potential use as tablet excipient Casettari L, Bonacucina G, Morris GA, Perinelli DR, Lucaioli P, Cespi M, Palmieri GF
133 - 144	Simulation of shock-powder interaction using kinetic theory of granular flow Liu HX, Guo YC, Lin WY
145 - 153	Fluid bed drying and agglomeration of phytopharmaceutical compositions Benelli L, Cortes-Rojas DF, Souza CRF, Oliveira WP
154 - 164	A mathematical model considering the interaction of bubbles in continuous casting mold of steel Zhang T, Luo ZG, Liu CL, Zhou H, Zou ZS
165 - 175	Investigation of coating layer morphology by micro-computed X-ray tomography Sondej F, Buck A, Koslowsky K, Bachmann P, Jacob M, Tsotsas E
176 - 190	FDLBM simulation of entropy generation due to natural convection in an enclosure filled with non-Newtonian nanofluid Kefayati GHR
191 - 196	Preparation of CeO2 nano-support in a novel rotor-stator reactor and its use in Au-based catalyst for CO oxidation Wang HR, Li YW, Zhang Y, Chen JF, Chu GW, Shao L
197 - 202	Effectiveness of wick-debinding inside powder bed for ceramic laminates made by tape casting Gorjan L, Blugan G, Graule T, Kuebler J
203 - 209	Optimization of gravity flow discharge chutes under the speed dependent resisting forces: Maximizing exit velocity Salinic S, Obradovic A, Rusov S, Mitrovic Z, Stokic Z
210 - 219	Exploring the interplay between abrasive attrition and separation in cyclones Freireich B, Kodam M, Jacob K
220 - 229	Carbon dioxide storage in olivine basalts: Effect of ball milling process Rigopoulos I, Petallidou KC, Vasiliades MA, Delimitis A, Ioannou I, Efstathiou AM, Kyratsi T