| 1837 - 1839 |
Mechanism of material removal under high stress abrasive wear conditions under varying experimental conditions
Dasgupta R, Modi OP, Yadav MS, Yegneswaran AH |
| 1841 - 1843 |
Synthesis of spinel lithium manganate powders using an inverse emulsion process
Lu CH, Saha SK |
| 1845 - 1848 |
Investigation of the carbothermal reduction of Ti2O3 in argon and nitrogen atmospheres
Berger LM |
| 1849 - 1851 |
Enhanced gas-solid reaction after extended milling
Welham NJ |
| 1853 - 1856 |
Electric arc generated (Bredig) palladium nanoparticles: Surface analysis by X-ray photoelectron spectroscopy for samples prepared at different pH
Mucalo MR, Bullen CR |
| 1857 - 1858 |
Investigation of superconductivity in BeB2 synthesized by the solid state reaction method
Mori T |
| 1859 - 1861 |
In situ synthesis of novel composites in the system Al-Zr-O
Zhao YT, Sun GX |
| 1863 - 1864 |
Effect of Al content on the lamellar spacing in two-phase TiAl alloys
Tang JC, Huang BY, Zhou KC, Liu WS, Liu Y, He YH |
| 1865 - 1867 |
Ethanolthermal synthesis to gamma-Cul nanocrystals at low temperature
Liu YF, Zhan JH, Zeng JH, Qian YT, Tang KB, Yu WC |
| 1869 - 1872 |
Microband substructure in pure titanium fabricated by powder metallurgical process with hot pressing at 1100 degrees C under a pressure of 20 MPa
Chu CL, Yin ZD, Lin PH, Zhu JC, Shen GJ |
| 1873 - 1875 |
Preparation and phase transition of superfine boehmite powders with different crystallinity
Lu JS, Gao L, Guo JK |
| 1877 - 1879 |
Effect of interchain crosslinking on the shrinkability of the blends consisting of grafted poly (ethylene vinyl acetate) and polyurethane elastomer
Mishra JK, Das CK |
| 1881 - 1883 |
Crystal structure and electric conductivity of the NASICON-related solid solution NaTi2P3-XAsXO3 synthesized hydrothermally
Shimanouchi-Futagami R, Nishimori M, Nishizawa H |
| 1885 - 1888 |
Toughening of tape cast Bioglass (R) by lamination with stainless steel 316L
Clupper DC, Mecholsky JJ |
| 1889 - 1891 |
A simple approach for determining the in situ fracture toughness of ceramic platelets used in composite materials by numerical simulations
Cannillo V, Corradi A, Leonelli C, Boccaccini AR |
| 1893 - 1896 |
CO2 separation characteristics of ZSM-5 composite membranes synthesized by the hydrothermal treatment
Kwak BI, Hyun SH, Kim GT |
| 1897 - 1899 |
Compatibility of YBa2Cu3O6+delta superconductor with YBa3Ti2O8.5 compound
Yu Z, Ang C |
| 1901 - 1904 |
Fractographic interpretation of the fatigue crack propagation behavior of polystyrene and polystyrene/polyethylene blends
Bureau MN, Denault J, Dickson JI |
| 1905 - 1907 |
The influence of temperature on the mode I fracture behavior of wood
Reiterer A |
| 1909 - 1911 |
Fatigue failure mechanisms of vanadium alloy/stainless steel brazed joints
Gan YX, Aglan HA, Steward RV, Chin BA |
| 1913 - 1915 |
Grain refinement of 1050 aluminum alloy by friction stir processing
Saito N, Shigematsu I, Komaya T, Tamaki T, Yamauchi G, Nakamura M |
| 1917 - 1920 |
Structure and composition of laser produced WC alloyed layers on M2 high-speed steel
Riabkina-Fishman M, Rabkin E, Galun R, Maiwald T, Mordike BL |
