| 1341 - 1343 |
A strong texture correlation between (Bi,Pb)(2)Sr2Ca2Cu3Ox and its precursor (Bi,Pb)(2)Sr2Ca2Cu2Ox
Mao CB, Zhou LA, Wu XZ, Sun XY |
| 1345 - 1347 |
X-ray and neutron diffraction study of Fe-(15 to 29)Cr-11Ni-0.5N steels
Baeva M, Beskrovnyi A, Jadrovski E, Danilkin S |
| 1349 - 1351 |
Preparation of laminated hydroxyapatite/zirconia sintered composite with the gradient composition
Matsuno T, Watanabe K, Ono K, Koishi M |
| 1353 - 1356 |
Microstructural evolution of modified 9Cr-1Mo steel
Dwivedi VS, Jha BK |
| 1357 - 1362 |
Study of the role of Mg and Zn in the directive oxidation of Al alloys
Kim IS, Lee SJ |
| 1363 - 1365 |
Physical and optical properties of aqueous L-arginine phosphate (LAP) solution for single-crystal growth
Kim YK, Lal RB |
| 1367 - 1370 |
The effect of heating rate on the reactive sintering of Ti-48%Al elemental powder mixture
Lee TW, Lee CH |
| 1371 - 1373 |
Electrical properties of CdSe photovoltaic electrodeposits in a marine environment
Mitsis A, Loizos Z, Dervos C, Vassiliou P, Kollia C, Spyrellis N |
| 1375 - 1380 |
Microstructured of a two-phase gamma ＇(Ni3Al)-gamma(Ni(Al)) intermetallic alloy after cold-rolling and annealing
Bystrzycki J, Varin RA |
| 1381 - 1383 |
The effects of primary silicon particles on the sliding wear behavior of aluminum-silicon alloys
Prasad BK, Venkateswarlu K, Modi OP, Jah AK, Das S, Dasgupta R, Yegneswaran AH |
| 1385 - 1388 |
Novel gold-polypyrrole anisotropic colloids: a TEM investigation
Selvan ST, Nogami M |
| 1389 - 1391 |
Rapid rate sintering of nano-grained ZrO2-based composites using pulse electric current sintering method
Yoshimura M, Ohji T, Sando M, Niihara K |
| 1393 - 1394 |
Structure transformation induced in natural graphite during ultrasonic fragmentation
Pan W, Liu Y, Du LH |
| 1395 - 1396 |
C-60-containing epoxy resin
Lu ZH, Goh SH, Lee SY |
| 1397 - 1399 |
Pull-out test of clathrate-hydrate films formed at water/hydrochlorofluorocarbon interfaces
Ohmura R, Mori YH |
| 1401 - 1402 |
Preparation of Bi2Se3 quantum dots by dissolution of crystalline powder in acetonitrile
Comor MI, Dramicanin MD, Rakocevic Z, Zec S, Nedeljkovic JM |
| 1403 - 1405 |
Difference in as-cast structures of centrifugal casting heat-resistant alloy caused by exerted electromagnetic field and cooling conditions
Wu XQ, Zhan Q, Yang YS, Hu ZQ |
| 1407 - 1408 |
A reinvestigation of the constitution of the partial system TiSi-Si
Du Y, Schuster JC |
| 1409 - 1410 |
Comment on "Behavior of turbostratic boron nitride under high pressure and temperature in the presence of a non-conventional catalyst"
Bocquillon G |
| 1411 - 1413 |
Thermal conductivity of injection molding mixture with different levels of stearic acid adsorption on particle surface
Liu DM |
| 1415 - 1419 |
Evidence for uniaxial drawing in the fibrillated microstructure of auxetic microporous polymers
Alderson KL, Alderson A, Webber RS, Evans KE |
| 1421 - 1425 |
Elastic strain energy change during matrix cracking in unidirectional, fiber-reinforced ceramic composites
Hsueh CH |
