| 4869 - 4877 |
Effect of pigmentation on the microstructure and properties of rotationally molded polyethylene
Cramez MC, Oliveira MJ, Crawford RJ |
| 4879 - 4885 |
Transient creep associated with grain boundary sliding in fine-grained single-phase Al2O3
Yoshida H, Sakuma T |
| 4887 - 4892 |
Development of glass frit free metallization systems for AIN
Adlassnig A, Schuster JC, Reicher R, Smetana W |
| 4893 - 4903 |
Processing and creep resistance of nickel/yttria composites
Sun LC, Shaw LL |
| 4905 - 4909 |
Probing of micromechanical properties of compliant polymeric materials
Tsukruk VV, Huang Z, Chizhik SA, Gorbunov VV |
| 4911 - 4915 |
The chemical and morphological properties of boron-carbon alloys grown by plasma-enhanced chemical vapour deposition
Zhang D, McIlroy DN, O'Brien WL, De Stasio G |
| 4917 - 4921 |
Time-dependent hardness of particulate-filled composites
Suwanprateeb J |
| 4923 - 4928 |
Electrical conductivity of ferric chloride-doped poly(acrylic acid-divinylbenzene)
Yousaf SM, Raza S, Ahmad Z, Khwaja FA |
| 4929 - 4936 |
Thermodynamic calculation of phase equilibria in the Ti-Co and Ni-Sn systems
Nash P, Choo H, Schwarz RB |
| 4937 - 4942 |
Hollow alumina microspheres from boehmite sols
Chatterjee M, Enkhtuvshin D, Siladitya B, Ganguli D |
| 4943 - 4951 |
The creep and thermal stability characteristics of a unidirectionally solidified Al2O3/YAG eutectic composite
Waku Y, Nakagawa N, Wakamoto T, Ohtsubo H, Shimizu K, Kohtoku Y |
| 4953 - 4960 |
A new model for the transverse modulus of unidirectional fiber composites
Fu SY, Hu X, Yue CY |
| 4961 - 4969 |
Microstructure development in laser-processed Al-Ti-Ni alloys with 25 at. % Ti
Gunnaes AE, Olsen A, Tafto J |
| 4971 - 4976 |
Polypyrrole based microwave absorbers
Truong VT, Riddell SZ, Muscat RF |
| 4977 - 4985 |
Superplasticity of fine-grained Fe-C alloys prepared by ingot and powder-processing routes
Kim WJ, Taleff EM, Sherby OD |
| 4987 - 4990 |
Structure and magnetic properties of BaCoTiFe10O19 thin films with an easy-axis in-plane orientation
Gu BX |
| 4991 - 4999 |
Comparison of surface treatment methods for promoting the adhesion of glass on titanium
Van Landuyt P, Streydio JM, Delannay F, Munting E |
| 5001 - 5006 |
Combustion synthesis, powder characteristics and crystal structure of phases in Ce-Pr-O system
Rajendran M, Mallick KK, Bhattacharya AK |
| 5007 - 5014 |
Joining of silicon carbide using MgO-Al2O3-SiO2 filler
Lee HL, Nam SW, Hahn BS, Park BH, Han D |
| 5015 - 5023 |
Refinement of cast microstructure of hypereutectic Al-Si alloys through the addition of rare earth metals
Chang JY, Moon IG, Choi CS |
| 5025 - 5028 |
Synthesis of HMDS radical terminated perhydropolysilazane
Shimizu Y, Suzuki K, Funayama O |
| 5029 - 5036 |
On the effects of surface treatments on the mechanical strength of carbon fibres
Bertrand P, Vidal-Setif MH, Valle R, Mevrel R |
| 5037 - 5047 |
The measurement of compressive creep deformation and damage mechanisms in a single-phase alumina part I - Grain boundary sliding
Blanchard CR, Page RA |
| 5049 - 5058 |
The measurement of compressive creep deformation and damage mechanisms in a single-phase alumina part II - Correlation of creep cavitation and grain boundary sliding
Blanchard CR, Page RA, Spooner S |
| 5059 - 5067 |
Capillary flow behaviour of microcrystalline wax and silicon carbide suspension
Suwardie H, Yazici R, Kalyon DM, Kovenklioglu S |
| 5069 - 5077 |
Precipitations in an yttrium-containing low-expansion superalloy
Wang RM, Han YF, Li CZ, Zhang SW, Ping DH, Yan MG |
