| 1 - 16 |
Single fibre fragmentation test for assessing adhesion in fibre reinforced composites
Tripathi D, Jones FR |
| 17 - 22 |
Low temperature hydrothermal synthesis of Ba(Mg1/3Ta2/3)O-3 sol-derived powders
MacLaren I, Ponton CB |
| 23 - 28 |
Effect of the cooling rate on the dendrite arm spacing and the ultimate tensile strength of cast iron
Seah KHW, Hemanth J, Sharma SC |
| 29 - 33 |
The effective tensile failure stress of an uncracked brittle structure : failure at a blunt stress concentration
Smith E |
| 35 - 40 |
Control of the morphology and surface properties of nickel ferrite
McGarvey GB, Owen DG |
| 41 - 43 |
Effect of preparation conditions on the low frequency Raman spectrum of glassy As2S3
Mamedov S, Kisliuk A, Quitmann D |
| 45 - 53 |
Recycling of epoxy resin compounds for moulding electronic components
Iji M |
| 55 - 61 |
Characterization of strain in annealed Cu-Ni multilayers using X-ray diffraction
Chaudhuri J, Low K, Jankowski AF |
| 63 - 67 |
Upconversion luminescence of Er3+ in transparent SiO2-PbF2-ErF3 glass ceramics
Kawamoto Y, Kanno R, Qiu J |
| 69 - 72 |
Young's modulus-porosity relations : an analysis based on a minimum contact area model
Mukhopadhyay AK, Phani KK |
| 73 - 76 |
The influence of Ba(PO3)(2) on the formation characteristics of fluorophosphate glasses
Ozturk A |
| 77 - 83 |
On deformation twins and twin-related lamellae in TiAl
Jin Z, Gray GT |
| 85 - 89 |
Microwave dielectric properties of ceramics with compositions along the La2/3TiO3(STAB)-LaAlO3 tie line
Suvorov D, Valant M, Skapin S, Kolar D |
| 91 - 97 |
Formabilities of steel/aluminium alloy laminated composite sheets
Takuda H, Fujimoto H, Hatta N |
| 99 - 102 |
Function of modification and refinement of rapidly solidified master alloy Al-Ti-Sr
Bian XF, Lin XH, Liu XF |
| 103 - 108 |
Viscoelastic phenomena in the fracture of thermosetting resins
McKilliam G, Moltschaniwskyj G, Horrigan DPW |
| 109 - 116 |
Mossbauer spectroscopic study of heat-treated and control-cooled Fe3Al alloys
Bandyopadhyay D, Suwas S, Singru RM, Bhargava S |
| 117 - 131 |
Anisotropic etching of silicon crystals in KOH solution - Part III - Experimental and theoretical shapes for 3D structures micro-machined in (hk0) plates
Tellier CR |
| 133 - 137 |
SmBa2Cu3O6.5 seed fabrication for seeded peritectic solidification of YBa2Cu3O7-delta
Chow JCL, Lettow JS, Lo W, Cardwell DA, Leung HT, Shi YH |
| 139 - 145 |
Interaction of some pollutant oxides on durability of silicon carbide as a material for diesel vehicle filters
Dario MT, Bachiorrini A |
| 147 - 153 |
Determination of the true stress-strain behaviour of polypropylene
Kontou E, Farasoglou P |
| 155 - 159 |
Nanometre-sized silver halides entrapped in SiO2 matrices
Matz W, Pham MT, Mucklich A |
| 161 - 166 |
Production mechanism of polyzirconocarbo-silane using zirconium(IV)acetylacetonate and its conversion of the polymer into inorganic materials
Ishikawa T, Kohtoku Y, Kumagawa K |
| 167 - 171 |
Characterization of the electronic density of metals in terms of the bulk modulus
Serebrinsky SA, Gervasoni JL, Abriata JP, Ponce VH |
| 173 - 182 |
Effect of methane concentration on physical properties of diamond-coated cemented carbide tool inserts obtained by hot-filament chemical vapour deposition
Taher MA, Schmidt WF, Naseem HA, Brown WD, Malshe AP, Nasrazadani S |
| 183 - 188 |
The AgxCu1-xInS2 solid solutions with 0 <= x <= 1
Bodnar IV, Yasyukevich LV, Korzoun BV, Karoza AG |
| 189 - 197 |
Determining the toughness of plastically deforming joints
Thouless MD, Adams JL, Kafkalidis MS, Ward SM, Dickie RA, Westerbeek GL |
| 199 - 206 |
TEM lattice images and their evaluation by image analysis for activated carbons with disordered microtexture
Yoshizawa N, Yamada Y, Shiraishi M |
| 207 - 210 |
Superconductivity in (Bi,Pb)(2)Ca2Sr2Cu3-xVxOy
Nkum RK |
| 211 - 214 |
In situ enhancement of toughness of SiC-TiB2 composites
Cho KS, Choi HJ, Lee JG, Kim YW |
| 215 - 221 |
Microstructure of diffusional zirconia-titanium and zirconia-(Ti-6 wt% Al-4 wt% V) alloy joints
Correia RN, Emiliano JV, Moretto P |
| 223 - 227 |
Applicability of the rheological equation of state for thermoplastic composites
Bae YC, Lee MCH |
| 229 - 234 |
Glass formation and glass structure of the BiO1.5-PbO-CuO system
Hu Y, Liu NH, Lin UL |
| 235 - 239 |
Amorphization behaviour in mechanically alloyed Ni-Ta powders
Lee PY, Yang JL, Lin HM |
| 241 - 246 |
Electro-discharge consolidation of nanocrystalline Nb-Al powders produced by mechanical alloying
Rock C, Qiu J, Okazaki K |
| 247 - 252 |
Solution spinning of high-Tc oxide superconducting filament - Part VIII - The effect of degree of saponification of poly(vinyl alcohol) on the critical current density of YBa2Cu3Ox superconducting filament
Tomita H, Omori T, Goto T, Takahashi K |
| 253 - 258 |
Effect of the surface treatment on the room-temperature bonding of Al to Si and SiO2
Hosoda N, Kyogoku Y, Suga T |
| 259 - 263 |
Characterization of a solid solution of Cu in Al-Cu-SiCp metal matrix composites processed by spray atomization and co-deposition
Juarez-Islas JA, Campillo B, Perez R, Su S, Lavernia EJ |
| 265 - 270 |
Microstructure evolution of mechanical alloyed Ni-24 at % Si
Jang JSC, Tsau CH, Chen WD, Lee PY |
| 271 - 278 |
Study of electrical characteristics and microstructure of zinc oxide varistor through rate-controlled sintering
Huda D, El Baradie MA, Hashmi MSJ, Puyane R |
