| 689 - 699 |
Electrooptic studies on polymer-dispersed liquid-crystal composite films. III. Poly(methyl methacrylate-co-butyl acrylate)/E7 and poly(methyl methacrylate-co-butyl acrylate)/E8 composites
Kalkar AK, Kunte VV, Bhamare SA |
| 700 - 709 |
Moisture curing kinetics of isocyanate ended urethane quasi-prepolymers monitored by IR Spectroscopy and DSC
Daniel-da-Silva AL, Moura Bordado JC, Martin-Martinez JM |
| 710 - 718 |
New type of phenolic resin - The curing reaction of bisphenol a based benzoxazine with bisoxazoline and the properties of the cured resin. III. The cure reactivity of benzoxazine with a latent curing agent
Kimura H, Matsumoto A, Ohtsuka K |
| 719 - 725 |
Monitoring of cure-induced strain of an epoxy resin by fiber bragg grating sensor
Harsch M, Karger-Kocsis J, Herzog F |
| 726 - 731 |
Morphology and mechanical properties of styrene-ethylene/butylene-styrene triblock copolymer/high-density polyethylene composites
Yu XJ, Zheng Z, Lu JM, Wang XL |
| 732 - 743 |
Enfluence of nonionic polymers on the rheological and electrical properties of Egyptian bentonite
Mostafa BA, Assaad FF |
| 744 - 754 |
Radiation-induced graft copolymerization of acrylic acid/acrylonitrile onto LDPE and PET films and its biodegradability
El-Arnaouty MB, Ghaffar AMA, El Shafey HM |
| 755 - 765 |
Synthesis and characterization of melt-processable polyimides derived from 1,4-bis(4-amino-2-trifluoromethylphenoxy)benzene
Zuo HJ, Chen JS, Yang HX, Hu AJ, Fan L, Yang SY |
| 766 - 777 |
Weak interaction, marginal miscibility, and ring-band spherulites in blends of poly(vinylidene fluoride) with polyesters
Li SH, Woo EM |
| 778 - 783 |
Semiflexible random thermotropic copolymers from 8-(3-hydroxy phenyl) octanoic acid and 3-chloro-4-hydroxy benzoic acid/3,5-dibromo-4-hydroxy benzoic acid
Mitra S, Pillai CKS |
| 784 - 787 |
Ethynedithiol-based polyeneoligosulfides as active cathode materials for lithium-sulfur batteries
Trofimov BA, Myachina GF, Rodionova IV, Mal'kina AG, Dorofeev IA, Vakul'skaya TI, Sinegovskaya LM, Skotheim TA |
| 788 - 796 |
Tribological Behavior of short-fiber-reinforced polyimide composites under dry-sliding and water-lubricated conditions
Chen JS, Jia JH, Zhou HD, Chen JM, Yang SY, Fan L |
| 797 - 802 |
Preparation of poly(amic acid) and polyimide derived from 3,3',4,4'-benzophenonetetracarboxylic dianhydride with different Diamines by microwave irradiation
Li QT, Xu ZS, Yi CF |
| 803 - 809 |
Effective preparation and characterization of montmorillonite/poly(epsilon-caprolactone)-based polyurethane nanocomposites
Jeong EH, Yang J, Lee HS, Seo SW, Baik DH, Kim JH, Youk JH |
| 810 - 818 |
Water-repellent finishing of cotton fabrics by ultraviolet curing
Ferrero F, Periolatto M, Sangermano M, Songia MB |
| 819 - 824 |
Preparation and characterization of proton-conducting crosslinked diblock copolymer membranes
Lee DK, Kim YW, Choi JK, Min BR, Kim JH |
| 825 - 830 |
Properties of poly(butylene terephthalate) chain-extended by epoxycyclohexyl polyhedral oligorneric silsesquioxane
Zhou ZY, Yin NW, Zhang Y, Zhang YX |
| 831 - 839 |
Novel reactive compatibilization strategy on immiscible polypropylene and polystyrene blend
Hung CJ, Chuang HY, Chang FC |
| 840 - 845 |
High-molecular-weight polyurethanes prepared by one-step miniemulsion polymerization
Li CY, Li YH, Hsieh KH, Chiu WY |
| 846 - 853 |
Synthesis and thermal behavior of some anthracene-based copolymers obtained by diels-alder cycloaddition reactions
Grigoras M, Sava M, Colotin G, Simionescu CI |
| 854 - 862 |
Effect of the ultradrawing behavior of gel films of ultrahigh-molecular-weight polyethylene and low-molecular-weight polyethylene blends on their physical properties
Yeh JT, Chang SS, Wu TW |
| 863 - 871 |
Synthesis and characterization of pH sensitive Poly(PEGDMA-MAA) copolymeric microparticles for oral insulin delivery
Kumar A, Lahiri SS, Punyani S, Singh H |
| 872 - 880 |
Molecular simulation of structure and loading-drug character of poly(propylene-co-gamma-butyrolactone carbonate)
Lu LB, Liu SQ, Huang KL |
| 881 - 890 |
Immobilization of myoglobin from horse skeletal muscle in hydrophilic polymer networks
Castro-Forero A, Jimenez D, Lopez-Garriga J, Torres-Lugo M |
| 891 - 897 |
Physicochemical characterization and antioxidant activity of quercetin-loaded chitosan nanoparticles
Zhang YY, Yang Y, Tang K, Hu X, Zou GL |
| 898 - 908 |
Thermal properties of extruded/injection-molded poly(lactic acid) and biobased composites
Mohamed AA, Finkenstadt VL, Palmquist DE |
| 909 - 917 |
Preparation of poly(ether sulfone) nanofibers by gas-jet/electrospinning
Lin Y, Yao YY, Yang XZ, Wei N, Li XQ, Gong P, Li RX, Wu DC |
| 918 - 929 |
Processing and properties of mineral-interfaced cellulose fibre composites
Thunwall M, Boldizar A, Rigdahl M, Banke K, Lindstrom T, Tufvesson H, Hogman S |
| 930 - 938 |
Effect of the molecular architecture of graft copolymers on the phase morphology and tensile properties of PS/EVA blends
Soares BG, Moreira ACF, Sirqueira AS, Barbosa RV, Simao RA |
| 939 - 950 |
Toughening of unsaturated polyester resins with core-shell rubbers
Huang YJ, Wu JH, Liang JG, Hsu MW, Ma JK |
| 951 - 957 |
Thermal and dynamic mechanical Behavior of poly(vinyl chloride)/wood flour composites
Jiang HH, Kamdem DP |
| 958 - 965 |
Effect of the composition ratio of pimelic acid/calcium stearate bicomponent nucleator and crystallization temperature on the production of beta crystal form in isotactic polypropulene
Dou Q |
| 966 - 975 |
Engineering properties of poly(vinyl chloride)-poly (butyl methacrylate) semi-1 and semi-2 interpenetrating polymer networks
Chakrabarti R, Chakraborty D |
| 976 - 984 |
Highly exfoliated poly(epsilon-caprolactone)/organomontmorillonite nanocomposites prepared by in situ polymerization
Tarkin-Tas E, Goswami SK, Nayak BR, Mathias LJ |
| 985 - 992 |
Effect of the graft yield of maleic anhydride on the rheological behaviors, mechanical properties, thermal properties, and free volumes of maleic anhydride grafted high-density polyethylene
Chen Z, Fang PF, Wang HM, Wang SJ |
| 993 - 999 |
The preparation and characterization of chitosan wound dressings with different degrees of acetylation
Qin YM |
| 1000 - 1005 |
Effect of silane KH-550 to polypropylene/brucite composite
Ma ZL, Wang JH, Zhang XY |
| 1006 - 1019 |
Modeling of coat-hanger die under vibrational extrusion
Qu JP, Zhang XM |
| 1020 - 1028 |
Simultaneously improved toughness and dielectric proverties of epoxy/core-shell particle blends
Wan WT, Yu DM, He J, Xie YC, Huang LB, Gu XS |
| 1029 - 1038 |
Preparation and crystalline analysis of high-grade bamboo dissolving pulp for cellulose acetate
He JX, Cui SZ, Wang SY |
| 1039 - 1046 |
Effect of fractional free volume and T-g on gas separation through membranes made with different glassy polymers
Recio R, Lozano AE, Pradanos P, Marcos A, Tejerina F, Hernandez A |
| 1047 - 1056 |
Sorption of binary liquid mixtures in methacrylate-based biomaterials; simultaneous determination of the diffusion coefficients and the uptake fraction at equilibrium of the components of ethanol-water mixtures by a new iterative method
Sideridou ID, Papanastasiou GE |
| 1057 - 1065 |
Use of a biomaterial as a thickener for textile ink-jet printing
Yuen CWM, Ku SKA, Kan CW |
| 1066 - 1070 |
Development of correlation between potassium hydroxide number and conductivity of concentrated natural rubber latex
Walpalage S, Ganga I, Silva KMD |
| 1071 - 1079 |
Influence of diazo pigment on polycarbonate photodegradation
Saron C, Felisberti MI, Zulli F, Giordano M |
| 1080 - 1090 |
Characterization of chitosan/caseinate films
Pereda M, Aranguren MI, Marcovich NE |
| 1091 - 1099 |
Silica fiber-polybenzoxazine-syntactic foams; Processing and properties
Kumar KSS, Nair CPR, Ninan KN |
| 1100 - 1107 |
Synthesis of tercopolymer BA-MMA-VTES and surface modification of nano-size Si3N4 with this macromolecular coupling agent
Xia R, Li MH, Zhang YC, Zhu QR, Qian JS |
| 1108 - 1115 |
Melt viscosity reduction of polycarbonate with low molar mass liquid crystals
Motong N, Thongyai S, Clarke N |
| 1116 - 1123 |
Polymer nanocomposites based on needle-like sepiolite clays: Effect of functionalized polymers an the dispersion of nanofiller, crystallinity, and mechanical properties
Bilotti E, Fischer HR, Peijs T |
| 1124 - 1132 |
Phase Behavior on the binary and ternary mixtures of poly(isooctyl acrylate) plus Supercritical fluid solvents plus isooctyl acrylate and CO2+ isoodyl acrylate system
Byun HS, Park YJ, Lim JS |
| 1133 - 1141 |
Furan-thiophene copolymers: Electrosynthesis and electrochemical behavior
Alakhras F, Holze R |
| 1142 - 1146 |
Effect on the anti-felt properties of atmospheric pressure plasma treated wool
Cai ZS, Qiu YP |
| 1147 - 1153 |
Evaluation of tribological performance of surface-treated carbon fiber-reinforced thermoplastic polyimide composite
Li J, Cheng XH |
| 1154 - 1162 |
Reinforcing effect of organoclay in rubbery and classy epoxy resins, part 1: Dispersion and properties
Ngo TD, Ton-That MT, Hoa SV, Cole KC |
| 1163 - 1168 |
Properties of surface-modified multiwalled carbon nanotube filled poly(ethylene terephthalate) composite films
Jin SH, Yoon KH, Park YB, Bang DS |
| 1169 - 1178 |
Effects of water on the long-term properties of Bis-GMA and Silylated-(Bis-GMA) polymers
Rivera-Torres F, Vera-Graziano R |
| 1179 - 1188 |
Preparation of a nanosilica-modified negative-type acrylate photoresist
Lin DJ, Don TM, Chen CC, Lin BY, Lee CK, Cheng LP |
| 1189 - 1193 |
Hollow porous poly(lactic acid) microspheres
Wang HL, Zuo JP, Yu SM, Chen JH, Song QS, Shi TJ |
| 1194 - 1200 |
Effects of the support-layer hydrophilicity on the active-layer formation of composite membranes
Jeon MY, Yoo SH, Kim CK |
| 1201 - 1206 |
Separation and recovery of gold(III) from base metal ions using melamine-formaldehyde-thiourea chelating resin
Aydin A, Imamoglu M, Gulfen M |
| 1207 - 1214 |
FTIR, H-1-NMR spectra, and thermal characterization of water-based Polyurethane/Acrylic hybrids
Pardini OR, Amalvy JI |
| 1215 - 1225 |
A novel direct aerodynamically assisted threading methodology for generating biologically viable microthreads encapsulating living primary cells
Arumuganathar S, Irvine S, McEwan JR, Jayasinghe SN |
| 1226 - 1234 |
Structure of polycondensates from hydroxymethylphenols
Christjanson P, Pehk T, Siimer K, Paju J |
| 1235 - 1242 |
Nonisothermal crystallization, melting behaviour, and morphology of polypropylene/linear bimodal polyethylene blends
Qin JL, Gao JG, Li ZT, Run MT |
| 1243 - 1251 |
Effect of cell-adhesive-molecule-coated poly(lactide-co-glycolide) film on the cellular Behaviors of olfactory ensheathing cells and Schwann cells
Park KS, Kim SM, Kim MS, Lee I, Rhee JM, Lee HB, Khang G |
| 1252 - 1256 |
HDPE chelate membranes prepared by preirradiation grafting for adsorption of heavy metal ions
Zu JH, Tong L, Liu XW, Sun GS |
| 1257 - 1268 |
Mechanical and thermal properties of Polyimide/Silica hybrids with imide-modified silica network structures
Khalil M, Saeed S, Ahmad Z |
| 1269 - 1279 |
Morphology and nonisothermal crystallization of a Polyacetal/Poly(epsilon-caprolactone) reactive blend prepared via a chain-transfer reaction
Kawaguchi K, Nakao H, Masuda E, Tajima Y |
| 1280 - 1287 |
Experimental results for the rheological and rheoloptical behavior of poly(ethylene terephthalate)/liquid-crystalline polymer blends
Cidade MT, Menon AR, Leal CR, Pillai CKS |
| 1288 - 1293 |
Synthesis and characterization of novel chain-extended bismaleimides containing fluorenyl cardo structure
Hu ZQ, Li SJ, Zhang CH |
| 1294 - 1300 |
Fourier transform infrared Spectroscopy in the study of the interaction between PVC and plasticizers: PVC/Plasticizer compatibility
Gonzalez N, Fernandez-Berridi MJ |
| 1301 - 1309 |
Fractionation and characterization of an ethylene-propylene copolymer produced with a MgCl2/SiO2/TiCl4/diester-type Ziegler-Natta catalyst
Dong Q, Fan ZQ, Fu ZS, Xu JT |
| 1310 - 1315 |
Kinetic study of the thermal degradation of poly(aryl ether ketone)s containing 2,7-naphthalene moieties
Liu SJ, Hou X, Fang CG, Ma RT, Jiang ZH |
| 1316 - 1319 |
Sorption properties of the iminodiacetate ion exchange resin, amberlite IRC-718, toward divalent metal ions
Noureddine C, Lekhmici A, Mubarak MS |
| 1320 - 1324 |
Enhancement of melt elasticity for poly(3-hydroxybutyrate-co-3-hydroxyvalerate) by addition of weak gel
Arakawa K, Yokohara T, Yamaguchi M |
| 1325 - 1336 |
Preparation and characterizations of direct methanol fuel cell membrane from sulfonated polystyrene/poly(vinylidene fluoride) blend compatibilized with poly(styrene)-b-poly(methyl methacrytlate) block copolymer
Piboonsatsanasakul P, Wootthikanokkhan J, Thanawan S |
| 1337 - 1342 |
Mechanical properties and water absorption of low-density polyethylene/sawdust composites
Kamel S, Adel AM, El-Sakhawy M, Nagieb ZA |
| 1343 - 1349 |
Synthesis and mesomorphic properties of cholesteric elastomers based on chiral mesogenic crosslinking agent
Hu JS, Li H, Liu C, Zhang BY, Li YX |
| 1350 - 1361 |
Mechanical and gas permeation properties of compatibilized polypropylene-layered silicate nanocomposites
Mittal V |
| 1362 - 1372 |
Elastic properties of cast films from propylene elastomers
Tsou AH, Lyon MK, Chapman BR, Datta S |
