| S1 - S1 |
Comminution 2002 - Proceedings of the 10th European Symposium on Comminution and the 627th Event of the European Federation of Chemical Engineering, September 2-5, 2002, Heidelberg, Germany - Preface
Forssberg E |
| S3 - S17 |
Material properties in fine grinding
Peukert W |
| S19 - S30 |
Comminution of non-brittle materials
Schubert G, Bernotat S |
| S31 - S41 |
Dispersing nanoparticles in liquids
Muller F, Peukert W, Polke R, Stenger F |
| S43 - S54 |
On fragmentation and agglomeration phenomena in an ultrafine wet grinding process: the role of polyelectrolyte additives
Garcia F, Le Bolay N, Trompette JL, Frances C |
| S55 - S63 |
Optimization of continuous ball mills used for finish-grinding of cement by varying the L/D ratio, ball charge filling ratio, ball size and residence time
Schnatz R |
| S65 - S74 |
Dry fine comminution in a stirred media mill - MaxxMill((R))
Wang YM, Forssberg E, Sachweh J |
| S75 - S83 |
Centrifugal tube mill for finest grinding
Kurrer KE, Gock E, Vogt V, Florescu R |
| S85 - S92 |
Optimum revolution and rotational directions and their speeds in planetary ball milling
Mio H, Kano J, Saito F, Kaneko K |
| S93 - S101 |
Mill selection and process optimization using a physical grinding model
Kwade A |
| S103 - S117 |
Stress energy distribution in different stirred media mill geometries
Stender HH, Kwade A, Schwedes J |
| S119 - S122 |
Vibration mill results in the light of stress intensity and number of stressing events
Bernotat S |
| S123 - S128 |
Investigation of grindability of diasporic bauxites in dry, aqueous and alkaline media as well as after high pressure crushing
Csoke B, Hatvani Z, Papanastassiou D, Solymar K |
| S129 - S136 |
Effect of certain trace elements on the grindability of cement clinkers in the connection with the use of wastes
Opoczky L, Gavel V |
| S137 - S145 |
Fine classification with vaned rotors: at the outer edge of the vanes or in the interior vane free area?
Nied R |
| S147 - S154 |
Investigations concerning the separation mechanism in deflector wheel classifiers
Bauder A, Muller F, Polke R |
| S155 - S164 |
Production of powder coatings with defined particle size distribution by grinding and inline classification
Wadenpohl C |
| S165 - S172 |
Amorphous ultrafine particle preparation for improvement of bioavailability of insoluble drugs: grinding characteristics of fine grinding mills
Choi WS, Il Kim H, Kwak SS, Chung HY, Chung HY, Yamamoto K, Oguchi T, Tozuka Y, Yonemochi E, Terada K |
| S173 - S181 |
Comparison of various milling technologies for grinding pharmaceutical powders
Nakach M, Authelin JR, Chamayou A, Dodds J |
| S183 - S190 |
Comminution of crystalline material by ultrasonics
Teipel U, Leisinger K, Mikonsaari I |
| S191 - S198 |
Application of high-pressure waterjets for comminution
Kuyumcu HZ, Rolf L |
| S199 - S208 |
High-performance sonic impulses - an alternative method for processing of concrete
Linss E, Mueller A |
| S209 - S217 |
Coarse crushing of brittle rocks by compression
Unland G, Szczelina P |
| S219 - S225 |
Modelling and simulation of particle breakage in impact crushers
Nikolov S |
| S227 - S237 |
Modelling fragment size distribution using two-parameter Weibull equation
Cheong YS, Reynolds GK, Salman AD, Hounslow MJ |
| S239 - S248 |
The effect of a grinding aid on comminution of fine limestone particle beds with single compressive load
Oettel W, Husemann K |
| S249 - S254 |
Cross piston press for high pressure comminution of fine brittle materials
Reichardt Y, Schonert K |
| S255 - S265 |
Characterisation of grinding media wear by visual texture
Pons MN, Belaroui K, Simer N |
| S267 - S277 |
Measurement of the load-deformation response from impact-breakage of particles
Tavares LM, King RP |
| S279 - S289 |
Transfer of fracture mechanical concepts to bulk solids attrition in pneumatic conveying
Frye L, Peukert W |
| S291 - S298 |
Intensifying the attrition of mineral waste in stirrer mills
Schaaff F, Schneider M, Neesse T |
| S299 - S306 |
A microscale look at tumbling mill scale-up using high fidelity simulation
Herbst JA |
| S307 - S315 |
Application of multi-dimensional Markov chains to model kinetics of grinding with internal classification
Mizonov VE, Berthiaux H, Zhukov VP, Bernotat S |
| S317 - S327 |
Linear and nonlinear particle breakage processes in comminution systems
Fuerstenau DW, De A, Kapur PC |
| S329 - S338 |
Determination of material properties relevant to grinding by practicable labscale milling tests
Vogel L, Peukert W |
| S339 - S343 |
Overflow-control system for a hydrocyclone battery
Schneider M, Neesse T |
| S345 - S353 |
On-line determination of particle size during fine grinding based on luminescence properties of solids
Aman S, Tomas J |
| S355 - S363 |
Mechanical activation of various cements
Sekulic Z, Petrov M, Zivanovic D |
| S365 - S371 |
Mechanochemical processing of sulphidic minerals
Balaz P, Takacs L, Luxova M, Godocikova E, Ficeriova J |
| S373 - S378 |
Co-grinding LiCoO2 with PVC and water leaching of metal chlorides formed in ground product
Saeki S, Lee J, Zhang QW, Saito F |
| S379 - S383 |
Sorption purpose lime hydrate grinding
Sverak T |
| S385 - S393 |
The fundamentals of the comminution of metals in shredders of the swing-hammer type
Sander S, Schubert G, Jackel HG |
| S395 - S403 |
Mechanical and metallurgical study of the fragmentation of end-of-life goods in a scrap shredder
Russo P, Aboussouan L, Birat JP, Sander S, Jackel HG, Schubert G |
| S405 - S415 |
Size reduction by means of low-speed rotary shears
Woldt D, Schubert G, Jackel HG |
| S417 - S424 |
Required energy and structural breakdown at the process of dynamic cutting - comminution of polypropylene and aluminium
Wustenberg D, Kasper J |
| S425 - S434 |
Optimised technologies for cryogenic grinding
Wilczek M, Bertling J, Hintemann D |
