International Journal of Heat and Mass Transfer

International Journal of Heat and Mass Transfer, Vol.79 Entire volume, number list

ISSN: 0017-9310 (Print)

In this Issue (105 articles)

1 - 2	A note on the confusion associated with the interfacial heat transfer coefficient for forced convection in porous media Nakayama A
3 - 3	Thermal conductivity of highly loaded aluminium nitride - poly(propylene glycol) dispersions (vol 65, pg 592, 2013) Wozniak M, Danelska A, Rutkowski P, Kata D
4 - 11	Natural convection heat transfer on a vertical cylinder submerged in fluids having high Prandtl number Kang GU, Chung BJ, Kim HJ
12 - 23	Acoustic and heat transfer characteristics of an impinging elliptical synthetic jet generated by acoustic actuator Bhapkar US, Srivastava A, Agrawal A
24 - 33	Transient analysis of subcritical/supercritical carbon dioxide based natural circulation loops with end heat exchangers: Numerical studies Yadav AK, Gopal MR, Bhattacharyya S
34 - 53	A review of heat transfer and pressure drop characteristics of single and two-phase microchannels Asadi M, Xie GN, Sunden B
54 - 63	Experimental study on a novel loop heat pipe with both flat evaporator and boiling pool Lu X, Wei JJ
64 - 71	Thermal conductivity and contact resistance of mesoporous silica gel adsorbents bound with polyvinylpyrrolidone in contact with a metallic substrate for adsorption cooling system applications Sharafian A, Fayazmanesh K, McCague C, Bahrami M
72 - 81	An experimental research on the cooling performance of the turbine vane with an advanced duplex-medium combined cooling Xu L, Wang W, Gao TY, Gao JM
82 - 93	Measurement of the bubble nucleation temperature of water on a pulse-heated thin platinum film supported by a membrane using a low-noise bridge circuit Ching EJ, Avedisian CT, Carrier MJ, Cavicchi RC, Young JR, Land BR
94 - 104	Heat transfer during melting of graphene-based composite phase change materials heated from below Fan LW, Zhu ZQ, Zeng Y, Lu Q, Yu ZT
105 - 115	Turbulent free convection in a porous cavity using the two-temperature model and the high Reynolds closure Carvalho PHS, de Lemos MJS
116 - 125	Analysis of non-Fourier conduction and radiation in a differentially heated 2-D square cavity Sasmal A, Mishra SC
126 - 136	Coupling model for heat transfer between solid and gas phases in aerogel and experimental investigation Bi C, Tang GH, Hu ZJ, Yang HL, Li JN
137 - 145	Conjugate natural convection in a square porous cavity filled by a nanofluid using Buongiorno's mathematical model Sheremet MA, Pop I
146 - 165	On the flow of a Walters-type B' viscoelastic fluid in a vertical channel with porous wall Marinca V, Herisanu N
166 - 175	Interferometry-based whole field investigation of heat transfer characteristics of dilute nanofluids Rao SS, Srivastava A
176 - 188	Investigation of Re-independence of turbulent flow and pollutant dispersion in urban street canyon using numerical wind tunnel (NWT) models Cui PY, Li Z, Tao WQ
189 - 200	Variable beam intensity profile shaping for layer uniformity control in laser hardening applications Wellburn D, Shang S, Wang SY, Sun YZ, Cheng J, Liang J, Liu CS
201 - 211	Flow characteristics of dual piezoelectric cooling jets for cooling applications in ultra-slim electronics Jang D, Lee KS
212 - 222	Numerical simulation of MHD nanofluid flow and heat transfer considering viscous dissipation Sheikholeslami M, Abelman S, Ganji DD
223 - 232	Prediction of pore size in high power density beam welding Wei PS, Chao TC
233 - 240	Transient heat transfer during depressurization from supercritical pressure Schulenberg T, Raque M
241 - 250	Numerical investigation of ammonia falling film absorption outside vertical tube with nanofluids Yang L, Du K, Niu XF, Zhang Y, Li YJ
251 - 268	Single bubble dynamics under microgravity conditions in the presence of dissolved gas in the liquid Aktinol E, Warrier GR, Dhir VK
269 - 278	Heat transfer coefficient calculated using a linear pressure gradient assumption and measurement for flow boiling in microchannels Mirmanto M
279 - 290	Taylor bubble-train flows and heat transfer in the context of Pulsating Heat Pipes Mehta B, Khandekar S
291 - 299	Constructal design of thermoelectric power packages Bejan A, Lorente S, Kang DH
300 - 308	Keyhole collapse during high intensity beam drilling Wei PS, Wu JH, Chao TC, Chen LJ
309 - 313	Heat transfer enhancement mechanism of pool boiling with self-rewetting fluid Hu YX, Zhang SL, Li XY, Wang SF
314 - 323	Improved heat recovery from paraffin-based phase change materials due to the presence of percolating graphene networks Warzoha RJ, Fleischer AS
324 - 331	Heat transfer and phase change in a polystyrene packed bed during melting Tanoue K, Nagao M, Yoshida A, Nishimura T
332 - 341	Thermal characteristics and flow patterns of oscillating heat pipe with pulse heating Xian HZ, Xu WJ, Zhang YN, Du XZ, Yang YP
342 - 352	A novel concept to estimate the steady state heat flux from impinging premixed flame jets in an enclosure by numerical IHCP technique Hindasageri V, Vedula RP, Prabhu SV
353 - 361	Heat transfer to a horizontal cylinder in a shallow bubble column Tow EW, Lienhard JH
362 - 377	An enthalpy formulation for thermocline with encapsulated PCM thermal storage and benchmark solution using the method of characteristics Tumilowicz E, Chan CL, Li PW, Xu B
378 - 389	Conductive heat transfer in a rarefied polyatomic gas confined between coaxial cylinders Tantos C, Valougeorgis D, Pannuzzo M, Frezzotti A, Morini GL
390 - 396	Effect of bubble interactions on mass transfer in bubbly flow Aboulhasanzadeh B, Tryggvason G
397 - 407	Effect of change in surface condition induced by oxidation on transient pool boiling heat transfer of vertical stainless steel and copper rodlets Lee CY, Chun TH, In WK
408 - 416	Electrode geometry effects on microstructure determined by heat transfer and solidification rate during resistance spot welding Wei PS, Wu TH
417 - 431	Heat transfer and flow characteristics of spiral fin-and-tube heat exchangers: A review Pongsoi P, Pikulkajorn S, Wongwises S
432 - 436	Local single- and two-phase heat transfer from an impinging cross-shaped jet Rau MJ, Dede EM, Garimella SV
437 - 449	Transient radiative transfer in a complex refracting medium by a modified Monte Carlo simulation Yi HL, Wang CH, Tan HP
450 - 467	Reliability-based design optimization of pin-fin heat sinks using a cell evolution method Chen CT, Chen MH, Horng WT
468 - 471	Frequency analysis of macrosegregation measurements and simulations Voller VR, Vusanovic I
472 - 485	Effects of density and thermal conductivity variations on entropy generation in gas micro-flows Prabhu SV, Mahulikar SP
486 - 495	Radial two-phase thermal conductivity and wall heat transfer coefficient of ceramic sponges - Experimental results and correlation Wallenstein M, Kind M, Dietrich B
496 - 506	Entropy generation and heat transfer numerical analysis in pipes partially filled with porous medium Mandavi M, Saffar-Avval M, Tiari S, Mansoori Z
507 - 517	A fast numerical method for the analysis of the heat transfer performance of graded metallic honeycomb materials Zhang YC, Xu YN, Liu ST
518 - 525	Equivalence between the application of entransy and entropy generation Oliveira SD, Milanez LF
526 - 531	Heat transfer under high-power heating of liquids. 2. Transition from compressed to supercritical water Rutin SB, Skripov PV
532 - 550	A Coupled Level Set and Volume of Fluid method with multi-directional advection algorithms for two-phase flows with and without phase change Ningegowda BM, Premachandran B
551 - 560	Heat transfer and friction factor characteristics of turbulent flow through a circular tube fitted with vortex generator inserts Deshmukh PW, Vedula RP
561 - 572	Three-dimensional simulation on behavior of water film flow with and without shear stress on water-air interface Yu YQ, Cheng X
573 - 583	Effective temperature jump length and influence of axial conduction for thermal transport in superhydrophobic channels Cowley A, Maynes D, Crockett J
584 - 588	Interfacial thermal resistance of Cu-SWCNT nanowire in water Toprak K, Bayazitoglu Y
589 - 601	Assessment and calibration of an algebraic turbulent heat flux model for low-Prandtl fluids Shams A, Roelofs F, Baglietto E, Lardeau S, Kenjeres S
602 - 617	Assessment of subcooled boiling wall boundary correlations for two-fluid model CFD Prabhudharwadkar D, Lopez-De-Bertodano MA, Hibiki T, Buchanan JR
618 - 627	Experimental study on static flash vaporization of aqueous NaCl solution at different flash speed: Steam-carrying effect Zhang D, Zhao BC, Yan JJ, Yang QZ
628 - 638	Experimental study of TiO2-water nanofluid flow and heat transfer characteristics in a multiport minichannel flat tube Zhang J, Diao YH, Zhao YH, Zhang YN
639 - 646	Techno-economic optimization of plant for raw ethanol production based on experimental data Jacimovic BM, Genic SB, Budimir NJ, Jaric MS
647 - 654	Static and dynamic behavior of water droplet on solid surfaces with pillar-type nanostructures from molecular dynamics simulation Niu D, Tang GH
655 - 665	Optical parameters for characterization of thermal radiation in ceramic sponges - Experimental results and correlation Dietrich B, Fischedick T, Heissler S, Weidler PC, Woll C, Kind M
666 - 675	Sub-continuum thermal transport modeling using diffusion in the Lattice Boltzmann Transport Equation Chen C, Geer J, Sammakia B
676 - 688	Determination of thermal diffusivity, conductivity, and energy release from the internal temperature profiles of energetic materials Erikson WW, Cooper MA, Hobbs ML, Kaneshige MJ, Oliver MS, Snedigar S
689 - 693	Frost retardation on fin-tube heat exchangers using mass transfer characteristics with respect to air velocity Ye HY, Park JS, Lee KS
694 - 703	An experimental investigation on bubble dynamics and boiling crisis in liquid films Gong SJ, Ma WM, Gu HY
704 - 712	Heating and evaporation of a two-component droplet: Hydrodynamic and kinetic models Sazhin SS, Shishkova IN, Al Qubeissi M
713 - 719	Experimental investigation of the characteristics of cryogenic oscillating heat pipe Li Y, Wang QL, Chen SZ, Zhao BZ, Dai YM
720 - 726	Resonance-induced condensate shedding for high-efficiency heat transfer Migliaccio CP
727 - 735	Inverse analysis of heat transfer across a multilayer composite wall with Cauchy boundary conditions Niu RP, Liu GR, Li M
736 - 749	Bed-to-wall heat transfer coefficient in a supercritical CFB boiler at different bed particle sizes Blaszczuk A, Nowak W
750 - 758	Heat transfer and entropy generation in fully-developed mixed convection nanofluid flow in vertical channel Chen CK, Chen BS, Liu CC
759 - 768	On Gill's stability problem for non-Newtonian Darcy's flow Barletta A, Alves LSDB
769 - 782	Influence of thermal buoyancy on boundary layer separation over a triangular surface Chatterjee D, Ray S
783 - 789	Study of internal radiation with solute inclusions during Czochralski sapphire crystal growth Fang HS, Zhang QJ, Tian J, Wang S, Ma RH
790 - 795	Modeling of frost build-up on parallel-plate channels under supersaturated air-frost interface conditions Loyola FR, Nascimento VS, Hermes CJL
796 - 806	Application of the weighted-sum-of-gray-gases model for media composed of arbitrary concentrations of H2O, CO2 and soot Cassol F, Brittes R, Franca FHR, Ezekoye OA
807 - 815	New delay differential equation models for heating systems with pipes Kicsiny R
816 - 828	Pool boiling enhancement through microporous coatings selectively electrodeposited on fin tops of open microchannels Patil CM, Kandlikar SG
829 - 837	Characteristics of an evaporating thin film of a highly wetting liquid in a groove Honda H, Makishi O
838 - 845	The influence of initial sizes and velocities of water droplets on transfer characteristics at high-temperature gas flow Volkov RS, Kuznetsov GV, Stizhak PA
846 - 857	Structure and transport properties of liquid alkanes in the vicinity of alpha-quartz surfaces Chilukoti HK, Kikugawa G, Ohara T
858 - 867	Experimental and numerical study of nanofluid flow and heat transfer over microscale backward-facing step Kherbeet AS, Mohammed HA, Salman BH, Ahmed HE, Alawi OA
868 - 875	Experimental observation of the critical heat flux (CHF) enhancement of the nanofluids by the electrical explosion of a wire in liquid Park EJ, Bang IC, Park HW
876 - 884	Development of a new condensation model for the nearly-horizontal heat exchanger tube under the steam flowing conditions Ahn TH, Yun BJ, Jeong JJ, Kang KH, Park YS, Cheon J, Jerng DW
885 - 892	A global model on temperature profile of buoyant ceiling gas flow in a channel with combining mass and heat loss due to ceiling extraction and longitudinal forced air flow Hu LH, Chen LF, Tang W
893 - 904	Saturated pool boiling from carbon nanotube coated surfaces at different orientations Ho JY, Leong KC, Yang C
905 - 915	Particle size distribution effects on preferential deposition areas in metal foam wrapped tube bundle Sauret E, Hooman K
916 - 924	Visualization study of boiling and condensation co-existing phase change heat transfer in a small and closed space with a boiling surface of enhanced structures Zhang GM, Liu ZL, Li YX, Gou YJ
925 - 929	Numerical study on gas diffusion in isotropic and anisotropic fractal porous media (gas diffusion in fractal porous media) Ma Q, Chen ZQ
930 - 944	MHD natural-convection flow in an inclined square enclosure filled with a micropolar-nanofluid Bourantas GC, Loukopoulos VC
945 - 953	3D-modelling of conjugate heat and mass transfers: Effects of storage conditions and species on wood high temperature treatment Oumarou N, Kocaefe D, Kocaefe Y
954 - 967	Effect of interface on the thermal conductivity of thermal barrier coatings: A numerical simulation study Wang L, Zhong XH, Zhao YX, Yang JS, Tao SY, Zhang W, Wang Y, Sun XG
968 - 980	Instability of three-dimensional flow due to rotation and surface-tension driven effects in a shallow pool with partly free surface Wu CM, Li YR, Liao RJ
981 - 988	Geometrical effects of wick structures on the maximum phase change capability Cai SQ, Bhunia A
989 - 1001	Development of a two-step electrodeposition process for enhancing pool boiling Patil CM, Santhanam KSV, Kandlikar SG
1002 - 1013	Experimental investigation of forced flow and heat transfer characteristics of phase change material slurries in mini-tubes Zhang P, Ye J
1014 - 1026	Multiplicity of solutions for laminar, fully-developed natural convection in inclined, parallel-plate channels Piller M, Polidoro S, Stalio E
1027 - 1033	Analytical modeling of temperature distribution in an anisotropic cylinder with circumferentially-varying convective heat transfer Sarkar D, Shah K, Haji-Sheikh A, Jain A
1034 - 1047	Validation study of a turbulence radiation interaction model: Weak, intermediate and strong TRI in jet flames Cumber PS
1048 - 1058	Nonuniform temperature boundary condition effects on data center cross flow heat exchanger dynamic performance Gao TY, Geer J, Sammakia B
1059 - 1069	The influence of windbreak wall orientation on the cooling performance of small natural draft dry cooling towers Lu YS, Gurgenci H, Guan ZQ, He SY
1070 - 1086	Simulation of supercritical fuel injection with condensation Qiu L, Reitz RD
1087 - 1095	Steady MHD flow and heat transfer of a third grade fluid in wire coating analysis with temperature dependent viscosity Nayak MK, Dash GC, Singh LP